Nie masz w koszyku żadnych produktów
 
English Polski Spanish 
Szukaj instrukcji do
 

(e.g. AA-V20EG JVC, ZX-7 Sony )
PayPal 1000+ rating Secure, Encrypted Checkout.
 
Kto jest w sklepie?
Sklep przegląda 5865 gości i 
1 zarejestrowany klient 
Kategorie
Informacje
Polecamy
Strona główna >> HARMAN KARDON >> SIGNATURE2.0 Instrukcja Obsługi
 
 0 szt. w koszyku 

HARMAN KARDON SIGNATURE2.0
Instrukcja Obsługi


Tweetnij o tym produkcie a dostaniesz $1.00 rabatu!
  • Plik do pobrania
  • Format PDF
  • Kompletna instrukcja
  • Język: English
Cena: $4.99

Opis HARMAN KARDON SIGNATURE2.0 Instrukcja Obsługi

Kompletna instrukcja obsługi w formie pliku PDF. Plik PDF zostanie dostarczony na Twój adres email po jego zakupieniu.

Instrukcje obsługi (czasami nazywane także podręcznikiem użytkownika) opisuja funkcje i sposób działania danego produktu.

Instrukcja jest dostępna w następujących językach: English

Plik nie jest jeszcze gotowy
Musisz najpierw dokonać zakupu.

Recenzje produktu
Dla tego produktu nie napisano jeszcze recenzji!

Tekstowy podgląd strony 30 (kliknij aby zobaczyć)
Signature 2.0
Once the reference level has been established, press the Menu Control button i so that Center is highlighted. Adjust the sound level using the � or � Menu Control buttons i until the volume from the center channel is equal to what you had just heard from the left front speaker. When the center channel level is set press the ¤ Menu Control button i until Right Front is highlighted and once again use the � or � Menu Control buttons i until the level is equal to the preceding speakers. Continue until all speaker locations have been set, and then quickly cycle through the list one more time to make certain that no additional adjustments are required. NOTE: For proper operation, the test tone should always be heard from the speaker location indicated in the on-screen menu. If the sound is being heard from a location other than the one shown on the screen there is a misconnection in the system. In that event, press the Menu button j three times to exit the menu system and then turn the unit off by pressing the Master Power Switch 1 on the front panel until the Standby LED 5 goes dark. Once the 2.0 and all amplifiers have been turned completely off (NOT placed in a standby mode) check all connections from the 2.0 to the power amplifier and from the amplifier to the speakers to find the incorrect connection. Once the problem is found and corrected, turn your system on again and resume the setup. When all speaker locations have been set so that the sound is equal, press the Menu button j to end the calibration and return to the Speaker Setup Menu. To complete the speaker setup, press the
¤
Indicate distance from Speakers to listening postition.

At the Speaker Dist Adj menu (Figure OSD-4) you will enter the information that will permit the 2.0 to automatically calculate the proper delay time for each analog and digital surround mode. Thanks to the advanced circuitry of the 2.0 it is no longer necessary to calculate delay times and enter them manually. It is important, however, that you have the distance from the preferred listening position to the front left/right, center and surround speakers measured and available before proceeding to the next step.
Speaker M F C S e r e u a o n r Dist Adj F F F F eet T T T

¤

System Configuration

s Std: nt L and ter: rounds:

R:10 10 10

Figure OSD-4

The first line on the menu allows you to change from the factory preset of measurement in feet to metric increments. If you prefer to enter the data in meters, make certain that the Meas Std line is highlighted and press the � Menu Control button i until Feet is replaced with Meters. Press the ¤ Menu Control button i when the desired measurement unit appears and move to the next line. At each of the next three lines, use the � or � Menu Control buttons i to change the setting so that the distance shown is as close as possible to the distance from your listening position to the speaker location that is highlighted. When the setting for a speaker position is complete, press the ¤ Menu Control button i to move to the next position. When all speaker distances have been entered, press the Menu button j to return to the Spkr Setup Menu to select any items that may require final fine tuning. Press the Menu button one more time to return to the Setup Menu so that final adjustments and configuration data may be entered.

Menu Control button i until Speaker Distances > is highlighted and press the � Menu Control button i to move to the next step.

26

Klienci kupując ten produkt kupili także

$4.99

SIGNATURE2.0 HARMAN KARDON
Instrukcja Serwisowa

Kompletna instrukcja serwisowa w formie pliku PDF. Instrukcje serwisowe zazwyczaj zawierają schemat…
>
Parse Time: 0.213 - Number of Queries: 107 - Query Time: 0.052